[-] tgrowl@lemmy.world 2 points 10 months ago

I’m still TS10 EDC all the way. Interested to see what recommendations you get here as I may look to change soon as well.

82
[DALL-E 3] GollumGP (lemmy.world)
submitted 10 months ago by tgrowl@lemmy.world to c/ai_art@lemmy.world

“Gollum MotoGP racer”

[-] tgrowl@lemmy.world 1 points 1 year ago

So I think I'm running into this problem a bit now. The reverse proxy and everything TCP and HTTPS works. The mail server I'm still trying to figure out. I'm using Wireguard to tunnel, do you know how to "bridge" that up to the VPS so that ports I need open to listen for incoming SMTP are also being listened on on the VPS?

[-] tgrowl@lemmy.world 2 points 1 year ago

This is the solution I went with. Had to tinker a bit with the KeepAlive settings, but otherwise smooth sailing now! Thanks!

40

Hi All,

Xpost from c/networking@lemmy.world

So since Reddit is out for me, I’m turning here to see if anyone has some insight or can comment on this. Anything you’ve got would be great!

Long and short, I made a quick decision and am now living in a “Spectrum Community” - whereby tenants are charged a fixed rate for Internet and TV and connect to a “mesh” network via captive portal where MAC addresses must be registered to the tennants. Everyone shares the same network, sorta, but it’s got that feature where no one can sniff each other (unless MAC addresses are registered to your name).

There’s some debate on posts regarding this, whether connecting your own gateway will cause an issue, but I would like to connect my own gateway / router. Now, I’d also like to port forward, as I run my own mail server, etc… which need this and a public IP address I can register with my domain in order for all the fun stuff to work.

I doubt I can connect the gateway / router and port forward as if the community were offering a “communal modem”, so the question becomes:

Can I defeat this “double NAT” by routing all traffic from MY gateway through a VPS? Then, can I tie my domain / proxy service to the public IP address of this VPS to make all my services work?

Other services I run: PiHole Unbound DNS resolving Emby Wireguard (for mobile access to PiHole) And other web based services

Again, thanks. Hopefully someone reads this and knows what I’m talking about. I believe in Lemmy.

[-] tgrowl@lemmy.world 3 points 1 year ago

Ok this is awesome. Thanks for posting this. Didn’t know this existed. It will now become my new favorite thing.

[-] tgrowl@lemmy.world 2 points 1 year ago

Is this your primary base out in the plains? Looks nice!

[-] tgrowl@lemmy.world 3 points 1 year ago

I clip it up out of the way when I’m not using it. Usually I try to sink the hang points about 1ft from the ceiling. Trying to put most of the force down on the wall as opposed to pulling outwards. Gives a good, slack hang.

10
submitted 1 year ago by tgrowl@lemmy.world to c/valheim@lemmy.world

skol!

[-] tgrowl@lemmy.world 1 points 1 year ago

Unfortunately not. A mule version would have been really cool though. I've got to be honest, I'm not sure which driver I got this with. I chose the frosty optic so its really nice and smooth.

[-] tgrowl@lemmy.world 2 points 1 year ago

Convoy has the osramber, and the Hank I got the E17A R9050 1850k :)

10

This is my indoor hang setup during the winter. Just a small fleece blanket suspended from either end. I use a small tie in the middle to bundle up the ends of the blanket to create an air pocket. One one side i have a bungee cord to pick up slack and stretch out a bit for my feet.

6
SOTC (lemmy.world)

  • Fenix UC30
  • Wurkkos TS10
  • Wurkkos FC11
  • Hank KR1
  • Hank D4V2
  • Convoy C8+
[-] tgrowl@lemmy.world 1 points 1 year ago

This is nice. I may steal it. To be honest, Reddit started dying for me when awards came out.

[-] tgrowl@lemmy.world 1 points 1 year ago

If you haven't already checked it out, The Ultimate Hang is full of pictures like this.

[-] tgrowl@lemmy.world 1 points 1 year ago

I need to get a top quilt. Which did you go with?

[-] tgrowl@lemmy.world 1 points 1 year ago

I actually just discovered this as well with my KR1. I took the pocket clip off of it though, so I’m not sure if that was a factor. It still has a separate o-ring for the tail cap so I wouldn’t have thought so. It was doing a tail stand in my shower when it started acting oddly like you say. Took it apart to find the tail cap had flooded. Still love it, though will be wary from now on.

view more: next ›

tgrowl

joined 1 year ago