[-] thenewred@lemmy.world 24 points 3 days ago

They were asking for a ride. She speaks Ukrainian. I'm guessing she wasn't bothered by it.

[-] thenewred@lemmy.world 2 points 3 days ago

I might have crossed my wires, it was probably just a forum post I misread. I happened to have new ceramic burrs so I went ahead and installed them.

I got closer to a perfect pull this morning after adjusting the right lever! Unfortunately I'm out of that coffee now so the process restarts with the next bag.

[-] thenewred@lemmy.world 2 points 4 days ago* (last edited 4 days ago)

New ceramic burrs.

I typically use light roast beans, apparently ceramic is better there.

Went through the hyperalignment procedure and got close but not perfect. Had to move on and get it back together at some point.

[-] thenewred@lemmy.world 2 points 4 days ago

Works the same, just inline. And this grinder has two

[-] thenewred@lemmy.world 3 points 4 days ago* (last edited 4 days ago)

I don't know about best, but these have been decent

Slurping Turtle (Easton)

Wild Ginger (Hilliard)

Aki Hana (Henderson)

27

Facepalm

[-] thenewred@lemmy.world 35 points 2 weeks ago

Me writing my resume in third person

172
109
submitted 5 months ago by thenewred@lemmy.world to c/science@lemmy.world

Just learned about this. A long read, but really interesting.

[-] thenewred@lemmy.world 117 points 5 months ago

Cisco Webex.

You think teams or zoom are annoying? This is much worse. The worst part is with some default meeting settings, a loud chime would play every time someone joined. People kept this on for meetings of 300+ people, then they started talking over the beeps once "the popcorn slowed down."

18
submitted 5 months ago by thenewred@lemmy.world to c/woodworking@lemmy.ca

Update to my previous post: https://lemmy.ca/post/7236274

[-] thenewred@lemmy.world 48 points 6 months ago* (last edited 6 months ago)

I'm a software engineer who does woodworking, and I approve this message.

But my favorite explanation: you grab your hand saw, and it works. You don't find out that the latest npm japanese-hand-saw-tooth package is incompatible with plywood, and you need to downgrade the package or buy new plywood to make a cut.

1191
submitted 7 months ago by thenewred@lemmy.world to c/memes@lemmy.ml

I don't know why I even bother opening the settings app

54
submitted 7 months ago* (last edited 7 months ago) by thenewred@lemmy.world to c/woodworking@lemmy.ca

Pretty happy with how this turned out, even months later

17
submitted 8 months ago by thenewred@lemmy.world to c/videos@lemmy.world
60
submitted 9 months ago by thenewred@lemmy.world to c/woodworking@lemmy.ca
35
submitted 10 months ago by thenewred@lemmy.world to c/climbing@lemmy.ml
129
submitted 10 months ago* (last edited 10 months ago) by thenewred@lemmy.world to c/woodworking@lemmy.ca

It's wild how similar woodworking and 3d printing are.

  1. Get a 3d printer
  2. Print things for the 3d printer

With woodworking

  1. Get a table saw
  2. Make things for the table saw

Now I can mix and match

Model: https://www.printables.com/model/205258-featherboard-with-replaceable-heads-m6

[-] thenewred@lemmy.world 38 points 10 months ago

Clearly you need to buy more belts to fill out your new belt organizer

449
Belt organizer (lemmy.world)
submitted 10 months ago* (last edited 10 months ago) by thenewred@lemmy.world to c/3dprinting@lemmy.world
[-] thenewred@lemmy.world 44 points 10 months ago

7/10, would've been better if she didn't have to remind me to make it so many times

[-] thenewred@lemmy.world 45 points 10 months ago

I asked my wife and she said "no"

71
submitted 10 months ago* (last edited 10 months ago) by thenewred@lemmy.world to c/3dprinting@lemmy.world

Had minimal clearance between these overhead shelves and the garage door, and the perfect light spacing was a few inches away from the cross bars. So I designed these snap fit brackets to offset the lights inline.

The lights make a huge difference, much more pleasant to work in the garage.

What I learned:

  • there is some sag because the screws aren't at the top of the bracket. I would add a tab that protrudes on the side so I could add a screw higher.
  • the screw face split on layer lines on a few of these. Still works but not perfect, so I would make the screw face thicker.

Also printed cable management clips

[-] thenewred@lemmy.world 32 points 10 months ago

I used the tools I bought earlier to justify those purchases

view more: next ›

thenewred

joined 1 year ago