119
submitted 4 months ago by Grippler@feddit.dk to c/coffee@lemmy.world

Haven't really used a mocha pot before, so I'm experimenting a little to find the right grind settings and ratios for my taste. Normally brew espresso on a flair classic. Went with this more modern design from bialetti because it also works on induction stoves.

you are viewing a single comment's thread
view the rest of the comments
[-] TDCN@feddit.dk 11 points 4 months ago* (last edited 4 months ago)

I'll just leave my usual copy pasta here that i hope will be a helpful guide. This is what I do for getting the best coffee out of a mocha pot.

This method gives me perfect coffee every time, but your milage may vary so don’t be afraid to experiment.

Grind to filter coffe size or maybe a bit finer. Don’t go to espresso level or it’ll just clog the brewer and burn the coffee. It is generally not super sensitive to grind size so don’t worry too much. If in doubt go corser.

Always, always weigh the coffe! I found that they are actually quite sensitive to the amount of coffe you put in. Ever since a started weighing the beans I’ve never had any issues with it. If you cannot get a nice consistent flow through the entire brew and it begins to sputter too early you most likely filled it too much. So rather than fiddle with the grind size, you should instead fill it a little less next time. This is why you must weigh the beans. I use 12-13g for the 2 cup, and 28-30g for the 6 cup version. If I go outside that range it won’t brew nicely. It’s that sensitive! Grind size does very little to change this

Use hot water. This first of speed up the brew but also makes it easier to control the pressure inside. So pour hot/freshly boiled water in, assemble, and put on a low to medium heat with the lid open so you can see when the coffee comes. When the coffee starts to come through turn it down to low low heat to get a nice, slow and consistent flow. For the 2 cup version it’s about 15-30 seconds and for the big 6 cup version i think it’s about 40-90 seconds. I can’t remember exactly so don’t worry too much as long as it’s consistent and nice and slow. No sputter until the very end when its done and you take it off the heat at the first sign of sputter.

Pour the coffee immediately. Otherwise it’ll slowly burn and turn bitter in the hot brewer. If you want to share the portion stir it a bit first since its much stronger at the bottom.

With this method i always get amazing coffee out of this little machine and i low it so much.

I usually drink it with plenty of milk. I just heat it with the Bialetti electric milk foamer, but a little pot and a whisk would give the same delicious foam. Don’t heat the milk too much. It should only be around 65 degrees or something like that or it changes the taste. For UHT treated milk i guess this doesn’t matter.

I hope this was helpful. So enjoy your coffee.

Additional debugging steps:

If you use a blade grinder: This is totally okay to do, and I’ve used one for years when I was a student and it worked just fine as well. You can grind pretty fine with that for the mokka pot. It’s difficult to go too fine, but again, if on doubt go corser. Much more importantly is to avoid clumps. Blade grinders tends to make clumps so try to stir them out a bit with a needle/scewer or a very thin fork.

Clumps causes channeling and easily makes it sputter and all the water goes through too fast since it cannot build the pressure needed to make a consistent flow.

Clogging causes it to go really slow and sputter almost immediately and it seems like not all the water wants to go through. This is because it builds up too much heat and pressure so when the coffee passed through the coffee it’s above 100C° so it instantly boils when it reaches the other side and gives a very harsh amd unpleasant taste.

And finally finally,FOR THE LOVE OF GOD CLEAN YOU MOKKA POT WITH SOAP! Don’t be fooled by what others are saying. It’s not building up “flavour” it is literally old and rancid coffee “flavours” you are building up. So please please clean you pot with soap and a soft sponge every single time.

[-] psud@aussie.zone 2 points 4 months ago* (last edited 4 months ago)

I agree with almost all of that, except I do fine filling the basket and wiping excess off with the back of a knife

But I do always use the same coffee on the same grind setting (I dialled it in years and years ago)

My point is volumetric measurement is fine if you're accurate and consistent

+1 on cleaning with soap. I put the basket through the dishwasher, and weekly hand wash the aluminium parts

[-] TDCN@feddit.dk 1 points 4 months ago

Even when i chance coffee type often and also use caffeine free coffee it almost always works if I use weight. But yes if you always just use the same coffee and grind setting then of course it'll work. I just find that even 1-2g over and it'll clog the brewer and it'll start sputtering before it is half way though

this post was submitted on 13 Jul 2024
119 points (97.6% liked)

Coffee

8433 readers
5 users here now

☕ - The hot beverage that powers the world!

Coffee gadgets - It's always great to learn about new gadgets. Please share your favorite hardware or full setups. It might inspire newcomers to experiment!

Local businesses - Please promote your local businesses. If you are not the owner of the business you are promoting, kindly ask the owner if it's okay. It would be great if the business has a physical store to include an exterior or interior shot.

founded 2 years ago
MODERATORS