3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
I used to be able to print things. Now for the past 6 months or so I've wasted spools upon spools trying to print anything and this always happens. I'm just about ready to sell this machine and give up on the whole thing.
Is there anything glaringly obvious that springs to any of your expert minds?
Ender 3 V3
Okay, I had the exact same printer and I likely know exactly what's going on because I also had adhesion issues in the beginning.
First off, if you have a textured plate, you should not need glue. Clean that plate thoroughly with soap and water and allow it to dry on a heated bed for a little while. You can also chase the water with alcohol to get it to dry quicker, but still let it get a good dry time.
Next, go into the printer and have it do a full recalibration for bed leveling and z offset height. Once it is done, go back into the printer and manually lower the z offset. The automatic z offset gets pretty close, but not quite good enough. For my printer I found that lowering it by -0.07 mm was a great starting point. Anytime you auto level or recalibrate the bed it will reset this number, and honestly you don't need to do it very often unless you perform maintenance or tighten something. My theory is that the automatic z offset height is sensing the very top of the texture of the bed, and is not taking the texture itself into consideration. You need to lower the nozzle on the z offset to get it to squish the plastic down into the texture of the bed.
After you make an adjustment, scale this print down to be 100 mm x 100 mm x 0.1 mm.
https://www.thingiverse.com/thing:6130105
It should only print one layer high. Check the quality of the print afterwards and pay close attention to the amount of squish and overlap of the plastic. The perfect amount of z offset should be completely smooth without any gaps. For my printer I tended to go a little bit lower just to get a little extra squish and bed adhesion, which showed some slight, raised ridges between the nozzle passes. This will smooth out by the second or third layer.
After all of this, consider raising your bed temperature to 60C for PLA. I found creality's default bed temp of 55 to be a little too conservative.
Lastly, if you are trying to print at 0.1 mm layer height, you need to override your first layer thickness to be 0.2 mm. Also, don't print anything tall with that layer height. I think there is some sort of error buildup that would cause my printer to knock things off of the bed after 145 mm.
It's a good printer but you definitely still have to tweak things like a typical printer. Overall, it was that z offset that was the culprit for a lot of my adhesion issues in the beginning. Anything after that just helps.
Edit: After looking it again at the picture, you can clearly see the gaps between the nozzle passes in your first layer. I am very confident that your z offset is too high. The plastic is lifting up a little bit and then when your printer heading for the second layer, it's colliding with the plastic and ripping things up.
Thank you! This is fantastically helpful!