this post was submitted on 03 Jul 2024
68 points (100.0% liked)

3DPrinting

18105 readers
228 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee
68
Inline filament drying prototype (www.youtube.com)
submitted 11 months ago by neclimdul@lemmy.world to c/3dprinting@lemmy.world
12 comments fedilink hide all child comments
 

Super simple prototype but if it works... Very cool idea!

all 14 comments
sorted by: hot top controversial new old
[–] empireOfLove2@lemmy.dbzer0.com 10 points 11 months ago* (last edited 11 months ago) (1 children)

This is a very good start. It will have limited effectiveness depending how exactly wet the filament is though, as the diffusion speed of water in plastic is low and it takes time to get the water actually out of the center to the surface to evaporate. The few minutes a filament sits in the inline dryer might be OK for surface moisture but will fail with wetter spools.

I think the ideal system would be to have a dry box that the heating unit and fan blow into, but then feed the filament out to the printer through a "stove pipe" that acts as the dry box exhaust. This way you're still drying the whole spool over time but then get that "final blast" to ensure the surface is as dry as possible. Make sure to insulate all walls such that you reduce how much heat you lose as the air passes through.

[–] neclimdul@lemmy.world 2 points 11 months ago

Yeah, I'm definitely interested to see some experiments. I was surprised it worked as well as it did but if it does it'd be super useful

[–] Imgonnatrythis@sh.itjust.works 6 points 11 months ago

I had wondered about this as well and think it's an awesome idea. Combo of good dry storage and printing from an active dry box seem to make this a non issue for me, but I like the idea. Maybe a coil of ptfe tubing that is fenestrated and with dessicant, a bit of heat and proper fan could do this quickly with minimal resistance. I bet its possible. I paid $45 I think for my firefly box. To me, I would place A value of about $90 on a system that did this well.

[–] callcc@lemmy.world 5 points 11 months ago* (last edited 11 months ago)

Argh finally someone tries the obvious solution. I was already considering it but was demotivated since it seemed so obvious and nobody seemed to have done it before.

This device could also probably be printed in PLA. I can't wait until I get my lab power supply so I can give this a try with a wire coil heater.

Edit: you could even mount some PTFE tubing mounted below a heated bed and pass air through it. That way you could potentially get away without a heating element and re-use some power usually lost.

[–] uninvitedguest@lemmy.ca 3 points 11 months ago

This was a great video. I enjoyed the creator's off key humour, for once.

[–] c10l@lemmy.world 3 points 11 months ago (1 children)

I thought it was pretty common knowledge that these dryers lack airflow. There are tons of printable wedges in printables.com and thingiverse.com to keep the lid open.

This alone speeds up drying massively. Adding a small fan to the opening might be even better but I never found it necessary.

[–] neclimdul@lemmy.world 2 points 11 months ago (1 children)

Maybe. I actually have a dehydrator I use with plenty of airflow.

But I think that only solves part of the problem because that makes it really good at drying the outside but it's still going to have trouble past the first couple layers. I think the fact moisture would also have a hard time penetrating means current options work well enough.for most people.

Anecdotally I can support this, recently I had a particularly old roll of petg that I dried for a larger print and later in the print started getting all stringy and messy.

[–] c10l@lemmy.world 1 points 10 months ago

I guess it depends on where you are. Where I am the air is a lot less humid than in other places, and I have the opposite effect. I put the filament roll in the dryer and start printing. As time passes, like the filament gets dryer and stringing reduces.