peregrin5

Democrats today are more likely to say they want their party to become moderate than they were four years ago, according to a Gallup poll published Thursday. The survey, conducted in the first week of President Trump’s second term, gauged partisan preferences on the ideological direction of respondents’ respective parties. Among Democrats and Democratic-leaning independents, 45 percent say they want their party to become more moderate, while 29 percent say they want the party to become more liberal, and 22 percent say they want the party to stay the same.

Haven't figured out how to make imgur posts show images on Lemmy yet.

These are some mugs i made a while back. Still trying to find my process. I drew the linework on Affinity Designer on the iPad and printed out the line work. Used a pencil to scratch out the line work and further carved it. Then painted with underglaze then brushed clear glaze on top after bisquing.

I think I would forgo the clear next time.

Learned my lesson. Will never do that again even though my boss’s boss told me to.

I’m officially quiet quitting and changed my LinkedIn to Open To Work, because fuck this job. The market sucks though so I’ll have to just fly under the radar for a few months until something better pops up.

I hate the fact that I have to work, and I’m just saving up enough money till I can get to the point where I can get some land and be self-sufficient on it.

I feel like I've dealt with some utterly uncalled for behavior from people at work recently. Like them blowing up at me about something if I'm just asking a polite question, etc.

I just tell myself "maybe they're having a bad day".

But I think about myself. I have bad days too. I never let it get to the point where I'm exploding at someone. I extricate myself from the situation, maybe fume about it privately, but I don't go on a rampage or yell at someone. In any rare case where I do end up letting a bit slip out I always apologize for it.

These people NEVER apologize to me for their outbursts. Why am I the only one walking on eggshells and trying to maintain professionalism, politeness, and kindess with people who seem to make no effort to regulate their own stress.

Someone having a bad day isn't an excuse to be bad human being with zero consequences. But it seems these people can get away with it because of how much power they hold in the company.

I honestly don't think I have it in me to as rude as some of these people so I'll probably just swallow their rudeness until the next time it happens while continuing to try to be kind and polite.

Have others had similar experiences?

PETG has always been more fraught than PLA for me but as of late it just looks like a mess.

I'm just trying to do calibration at this point and I'm getting this mess on the pressure advance test in Orca Slicer.

https://imgur.com/a/zbEn5FR

I get so much stringing, boogers, and just terrible prints. It didn't used to be this bad. Any tips?

I'm using a Snapmaker Artisan.

I'm a dumbass and had someone come out and install a 240v outlet (and 120v). The reason I'm a dumbass is I didn't measure and had them install it in a place it wouldn't work for the appliance I am using.

I need to move the outlet a lot closer to the breaker box so I won't need additional wire or material, less actually.

I'm debating doing this myself. I technically have an EE degree but my day job is primarily coding, and any electronics I've worked on are usually the micro variety. I am aware of all the electrical safety requirements and in terms of technicality/connections, I think I just need to copy what has already been done but just remove a bunch of wire and place the outlet closer.

Do you think this is something I could take on myself with some research? My brother-in-law is also a proper electrician and I can facetime him.

Or do you think I should just ask the guys who installed it back and have them do it?

I have a large space under our deck that is enclosed and have been turning into a sort of shed. Every time I go in there though I'm super itchy all over like something has been biting me. I don't see any insects though. However I am bad at noticing things like bugs.

Any ideas?

I'd like to say they could enjoy the company of more liberals if they didn't ban them on sight due to their desire to feel superior and inability to tolerate differing opinions, but I couldn't respond because I was banned. (Ban reason: "liberalism")

I’m getting the electrical for a kiln put in tomorrow and I’m pretty stoked. I’ve been doing pottery on and off for the last couple of years now and one of the bottlenecks has always been not being able to do my own firings.

I particularly like to test my own glazes and experimenting with stuff like that is hard to do in a community kiln. I’d feel so guilty if something happened and I ruined someone else’s piece, so I’ve been looking forward to doing my own firing.

Anyway, the problem now is deciding what kiln to get. My initial idea was just go get a Skutt KMT-1027-3. It’s expensive but I’m sure it would just work. (Price: ~$5000)

But I am kind of hacky too and I love a good electronics project, so I’m toying with the idea of getting a KilnSitter model of the 1027 and putting together my own controller with a Raspberry Pi. I would love to be able to control my kiln with some open source software from my phone like I can do with my 3D printers using Octoprint. (Price: ~$1500)

Then there is the question of whether or not the 1027 is too much kiln for me in the first place. It’s quite large and I am not a fast producer so it would probably take me a while to fill the kiln unless I was doing a lot of large objects or platters. But I like the ability to do these if I want to, so I don’t want to limit myself with a kiln that is too small. (Price: ~$3000)

There’s also one guy asking for $3500 for a used Skutt KM (non-touch) 1027 and I think he’s asking too much for a used kiln but it is cheaper than the brand new models and does include kiln furniture. So that’s another route. (~Price : ~$3500)

Any tips about which route I should take?

Welcome! This is an area to discuss pottery related topics and questions, and share cool pottery related pics.

This is the first time I’m making a community so still figuring things out here.