Setting up my server as a newbie some years ago, I did not have the ability to purchase more then one 8TB hard drive. Outgrew that rather quick and now I have two additional 16TB drives, in a Just A Bunch Of Disk configuration, mounted to different /mnt mount points. I know this is not ideal, but lacking the ability to expand further or buy new drives for a new zfs pool and transfer, I don't have much of a choice but to wipe the drives, set up a zfs raid and re-download everything.

I have everything set up in docker-compose files, so I'm pretty sure I just need to keep those and the folders where the configs are, modify the compose files with the new file structure and... I am unsure where to go from here. Will everything start being grabbed as soon as my dockers spin up? Is there an additional procedure I need to do to make sure I don't wipe my existing config files with blank empty ones? Is there an easier way of doing this?

I have an 8gb Raspberry Pi 4 that has been a workhorse for years. I keep it for my not intense but essential networking purposes, NetBoot.xyz, Homepage, etc., because I can run it over PoE (edit: Power over Ethernet), so it is always on as long as my network is up.

It is growing long in the tooth, and I find myself wanting to replace it with something a bit more capable. Looking at the 8gb Pi 5 at $80 plus another $30 for a PoE hat, I wonder if there is something out there that would be a better value for running PoE? Can you convert a micro pc over to PoE? Does anyone have any recommendations for computers that run off PoE or can be converted to PoE?

I am trying to set up a repository of knowledge for my job. Was thinking a wiki, but I need something that I can make as simple as possible for the end user, as some of them are not familiar with markdown or html. Is there a self hosted option that is dumb easy simple to navigate and edit for the end user?

I have this image in my head I can’t quite pull what musical it is from. It’s a 1950-60s western, in color, a woman is walking around a ranch singing about how everything would be different and everyone would treat her differently if she were a man. She was just talked over by her dad or older brother. May not have been a western, but I distinctly remember her on or near a fence post during the number. I do not remember any particular face or name attached to this film. Anyone have any ideas of what movie this was?

I am currently looking into upgrading storage for my homelab. The two routes I am looking at are grabbing a dell r730 or a disk array. They are both about the same price, but my major purchase concern is heat and noise. My office/homelab is in a 10x10 foot room. I have worked hard to get the sound floor at my desk to be around 44dB, and the temps to top off at 79f, 74 on a good day with the door open. Is a disk array going to add more heat and noise to the room than a dell r730 server running proxmox with trunas?

About a year go I bought one of those fanless four port routers. Ordered one with a celeron, they sent me one with an 11th gen i3. Since then, core temps will regularly spike to 100c and it will throttle. Took it apart and found this as a cooling solution, which I’m sure would work fine with a celeron, but they gave me an i3 1115g4, with a base frequency of 3.1ghz, which can’t dump heat into this aluminum slug fast enough. The bios does not let me lower the clocks, or save power anywhere else. My only solution to make this work is to improve the cooling solution.

Would love to do a tower cooler, but can’t find any place that produces one that will fit my mounting holes. Been looking at laptop solutions as well, but again I am running into bracket and mounting problems. Nothing shows dimensions so I don’t waste time and money on solutions that don’t fit.

I have found copper shims, ranging from .3mm to 1.5mm thickness in a 20mmx20mm form. The aluminum slug they used is 45x25x2.73. If I stack these shims with thermal compound in between, would I get better thermal conductivity than just the aluminum slug? Are there any better ideas than what I am coming up with? Would it just be cheaper to buy another router that is cooled correctly?

I have friends and relatives that would like to do some memory and compute intensive tasks, but lack the hardware locally. I have loads of ram doing nothing and a little compute to spare. Is there a way for me to set up some service accessible to them that would allow them to spin up VMs, similar to Linode or DigitalOcean? I know letting outside access to a proxmox server would be disastrous. I guess I could setup a VPN server into a virtualized proxmox server? Would rather find a way to point them to a url with a username and password and have them able to use my server as their vps like AWS or Linode.

Got this sickly looking peach tree in the end of May. After about a month I started seeing red/black spots on the leaves and it looked like something what eating them. Did some research and started spraying it with neem oil. The spots stopped happening on newer hight leaves, as well as the bite marks. Now all the leaves are falling off and it looks like this. Is it dead? Does it have any hope? What can I do to put it on life support and make it through the winter?

first off, thanks for everyone and their suggestions, and apologies for not responding back, was having issues with my personal lemmy instance.

I took everyone's advice and have gone test print crazy. I will attach the pictures to this post. I have tried to understand what I am looking at on my test prints in relation to what is not configured correctly on my printer. it's just not clicking. most of my prints look fine, the surface has good infill and the part looks ok from the outside, like benchie. but underneath, it looks like I am having either adhesion issues, bridging problems and support problems as well. but adjusting setting as suggested in here and here did not really improve anything, and in some cases made the print worse.

I am using the Flashprint slicer that came with the printer. I have tried cura and prusaslice and can't even get a print started on those, even with a raft. I'm sure they are better slicers that what Flashforge makes, but again, something just isn't clicking. any further advice would be greatly appreciated.

I am trying to finally get my homelab organized, and I need assistance visualizing my network. I am just wondering if there are tools out there that assist with this. I have tried the paint and gimp routes, and I find myself spending more time trying to make it look good and organized rather than actually mapping my network. Is there any utility out there that is purpose build just for visualizing network topology? Or am I better off with just graph paper, pencil and a straight edge?

Thinking of lining the inside side panels of my 48u rack with some sort of sound deadening material. Was going to go with rock wool or the cheap self adhesive foam bricks you can buy off amazon. Was thinking of doing the same thing to the ceiling above where my rack sits and the walls behind as well. Mainly trying to cut down on the echo and high frequency whines. Anyone have any advice or suggestions? Maybe talk me out of it, or some other solution?

Not sure if this has come up, but one UI element I liked from Apollo and “the-one-that-shall-not-be-named” was the floating button in a thread that would take you to the next top level comment in that thread. Not sure what this feature is called, but so far can’t find it in any Lenny/Kbin client. Is this something that is in Memmy’s pipeline?