3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
Hi all,
I'm doing an experiment with a cabinet for filament with a small dehumidifier in it. I can get it to sit at 35%, but not much lower. I've sealed the cabinet with foam tape, and dried most of the filament first.
Are there any tricks to help improve performance of the mini dehumidifier? Maybe adding more heat to the cabinet?
The goal would be to use Home Assistant and the humidity sensor to turn things on and off as needed.
Thanks!
Are you sure it's 35% ? I've found those cheap digital hygrometers to be off by 10-15%.
I bought a box and some say 10 and some say 20. I ended up buying several different brands and price ranges of hygrometers to try and figure out which ones were correct.
I use cereal boxes with desiccant and without any active dehumidifier they stay at ~25% despite being frequently opened and closed. So like others suggested, put a large flow-through bin of desiccant in and forget about it.
Also is that a compressor dehumidifier? I suspect it's a desiccant wheel because it's so tiny.
It's a compressor, which is probably the problem. I'm using a DH11 on ESPHome, so am pretty confident of the accuracy, it's down in the bottom center of the cabinet. (I designed these https://nowsci.com/only-sensor)
Edit: Also, what do you mean by flow-through?
Re: flow through
A mesh like container so all sides are exposed to air. Many 3d printed designs have channels so air can get into the middle of the desiccant container.
Ahh thanks. Also, as a correction, this thing may be a crappy peltier dehumidifier.
The DHT11 has been replaced twice with similarly-priced but more accurate models, first the DHT22 and then the AHT20. In my experience, the AHT20 is a lot better than the DHT22, mainly because its power consumption is far lower, so it doesn't mess up its readings by getting hot.
Also, at that size, I'd be very surprised if the dehumidifier has a compressor. It's much more likely that it's got a Peltier plate, and they're not very good. They use a lot of power to develop and maintain a fairly small temperature difference, so if they're in a confined space, they heat up the air quite a bit, and then the water from their tank will more easily evaporate.
If you're willing to spend some money, a solid state ion membrane dehumidifier might be better for a small cabinet than a compressor-based one, as it'll be easy to ensure the water goes out of the cabinet instead of into a container that can't be emptied without opening the cabinet and letting more humidity in. They're definitely not cheap, though. I think they're still under patent as there's only one manufacturer that I can find, so maybe they're the dehumidifier of the future even if they're not suitable right now.
While I'd rather have 2% accuracy than 5% on paper, it's been fine, and checking with higher quality sensor has always put me within 1%.
Also, I mentioned in another comment it was a peltier, and I'd love to do SS but just soooo expensive. :(