Wow, that's pretty impressive! I've always been a bit hesitant about making ocarinas, since I hear that shrinkage can heavily distort the sound it makes. How does it sound?
I'm a rank amateur at playing them really. It sounds good but is definitely a bit out of tune. Luckily with vessel flutes in general, you can just adjust the size of the holes to bring it back in tune again! In fact the designer of this one in particular lists 2 files, one with holes and one without. They recommend making your own holes, which is the better way to tune it, since it's easier to make a hole bigger than to make it smaller. Nevertheless, you can still make the holes smaller via successive layers of varnish/lacquer/etc.
Splendid, but can you time travel by playing it?
Not so far, but I haven't mastered the song yet either 😝
Hadn't heard of PHA before. Anything you can say about how it behaves in print?
Absolutely! It can be a teeny bit finicky compared ol' reliable PLA, but I think it's pretty worth it. The only real issue is that wide flat parts have a tendency to warp off the build plate? Here's what I've figured out so far about making it adhere extra well:
- Bed temp turned completely off!
- Use a fresh layer of a really good 3d printing adhesive. (If your adhesive is heat activated, 35C should be enough to activate without messing with the PHA)
- If you have an enclosure, open it up as much as possible. I noticed I have a lot more warping in my enclosed printer than my unenclosed one.
- Between the handful of 100% pure PHA brands that I'm aware of existing, one says full fan as early as possible and another says no fan at all unless you're doing lots of bridging/overhangs, so try out a few different fan settings.
- Put a big giant brim on it. Maybe even try one made out of a different material than the object itself, if you've got dual extrusion.
- The higher the infill percentage and the more solid bottom layers there are, the more it will warp. So avoid that where possible.
- Most slicers probably already print the first layer at a chunkier line width than the nozzle size, but feel free to jack up the line width even more.
- Set the first layer pattern to concentric or Hilbert curve, evens out the distribution of forces that cause warping.
- Finally, if all else fails... Rotate the object until it's sitting on a really impractical edge, then print it in sort of a "cradle" of support material. I use BVOH or PVA. Basically make as little of it touch the build plate as possible? I don't like this option because it requires dual extrusion and is pretty wasteful.
There, that's everything I know so far. This probably makes the warping sound a lot worse than it is. It's really not super terrible. You probably won't have to barely ever use any of these tips, and if you can get past the warping, every other aspect of printing with PHA works like a dream.
Thanks a lot! Think, I'll give it a try. Does it produce a lot of fumes/smell?
No prob! None whatsoever, as far I can tell
I haven't tried PHA. Sounds like I'd have to do the opposite of everything I do with PLA lol
Eyyy, someone else playing with PHA!
I have a bunch of PHA commentary (and experimentation) over on the kbin 3d-printing group:
https://kbin.social/m/3DPrinting/t/40862/PHA-filament-heat-resistance-testing
omg yeah, your stuff has been really helpful! there's so little info out there about it, I hope it catches on
3DPrinting
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)
Moderation policy: Light, mostly invisible