307
Very Specific Object: Made a wall mount for my NAS and its UPS (lemmy.world)
submitted 6 months ago by IMALlama@lemmy.world to c/3dprinting@lemmy.world
30 comments fedilink hide all child comments

I liked a few of the VSOs that were posted earlier and wanted to share two of my more recent creations.

This mount screws into an exposed 2x4 and lets me get my Synology DS418, its power brick, and UPS (APC BE600M1) off a table and into a lower dust area of my basement.

I'll upload the STLs to printables if anyone is interested, but be warned that the parts are fairly large.

In the spirit of showing parts under unflattering lighting, here's (nearly) the same angle with a different light source.

top 30 comments
sorted by: hot top controversial new old
[-] DABDA@lemmy.world 50 points 6 months ago

What kind of filament is that printed with and are you concerned about it failing over time? Especially if there's spinning disks in there I'd be paranoid as hell about it falling.

[-] charles@lemmy.world 36 points 6 months ago

This scares the hell out of me. Too much risk of damage. Heat, weight, and time.

[-] IMALlama@lemmy.world 12 points 6 months ago

There's basically no heat involved. It sounds like you're worried about creap, which is totally fair and something to be aware of. The parts are printed out of ASA and are very overbuilt, so there shouldn't be any cause for concern.

Creap video: https://youtu.be/88pk2cNOeGE?si=_JxBtYyYitBEin2Y

[-] PipedLinkBot@feddit.rocks 1 points 6 months ago

Here is an alternative Piped link(s):

https://piped.video/88pk2cNOeGE?si=_JxBtYyYitBEin2Y

Piped is a privacy-respecting open-source alternative frontend to YouTube.

I'm open-source; check me out at GitHub.

[-] rambos@lemm.ee 6 points 6 months ago

It looks beefy enough to me

[-] SzethFriendOfNimi@lemmy.world 3 points 6 months ago

I’d print it but using ABS

[-] IMALlama@lemmy.world 4 points 6 months ago

It's ASA, it'll be fine :)

[-] SzethFriendOfNimi@lemmy.world 3 points 6 months ago

Yeah. That’ll be good.

[-] Vytle@lemmy.world 1 points 6 months ago

This man has never heard of 3d2a :P

[-] IMALlama@lemmy.world 13 points 6 months ago

It's printed out of ASA, which basically doesn't creap. It's also wayyyy overbuilt for the amount of weight it's supporting. I'm not at all worried about it failing over time.

[-] einlander@lemmy.world 7 points 6 months ago

As long as it's not pla. That's a ticking time bomb.

[-] IMALlama@lemmy.world 5 points 6 months ago

It's ASA, should be more than fine :)

[-] owen@lemmy.ca 5 points 6 months ago

I think it looks fine, the layers are aligned appropriately and it seems at least 5mm thick

[-] Jayb151@lemmy.world 3 points 6 months ago

I disagree. It seems that the letters are along where the stress is, which can eventually cause determination. This part scares me when you consider how important what it's holding it's.

[-] threelonmusketeers@sh.itjust.works 4 points 6 months ago

letters

layers

determination

delamination?

it's

is

[-] KickMeElmo@sopuli.xyz 3 points 6 months ago

He said in another spot that it's ASA.

[-] GrayBackgroundMusic@lemm.ee 12 points 6 months ago

very !functionalprint@kbin.social appropriate, too.

[-] IMALlama@lemmy.world 12 points 6 months ago

Totally agree in the long term. For the time being, I've been focusing a bit more on posting in general interest communities. Even larger communities, like this one, aren't that active. I think this was the first post in 24 hours and a good day is something like 3 posts. Fragmenting conversation and duplicating posts probably isn't the answer - at least not right now.

See also: fixmyprint, Vorondesign, etc. I was fairly active in both on Reddit, but they're ghost towns here and most of the content that would have gone there on Reddit is in this single community instead.

That said, feel free to crosspost if you like.

[-] EmilieEvans@lemmy.ml 4 points 6 months ago

Much quieter than it was a few months ago.

[-] Whitebrow@lemmy.world 9 points 6 months ago

Looks fantastic. I recommend also printing a cover for the UPS sockets with removable covers for the plugs you wish to use as it looks like you have quite a bit of dust circulating there

[-] IMALlama@lemmy.world 3 points 6 months ago

Thanks! The NAS and UPS are now in a closet that's fairly dust free. Before they were in my basement and fairly close to the cat box and my woodshop. Getting everything into the lower dust closet was one of my motivators.

I should probably blow the UPS off with my air compressor though...

[-] jimmycrackcrack@lemmy.world 8 points 6 months ago

Reminds me of the PS2 with it's blue triangular stand.

[-] timo_timboo_@lemmy.world 1 points 6 months ago

Man, still have to get one of those

[-] owen@lemmy.ca 2 points 6 months ago

I like the color! Honestly thought they were painted at first glance

[-] IMALlama@lemmy.world 3 points 6 months ago

Thanks! It's Polymaker ASA in blue.

I bought two 3 kg spools of it because it was fairly cheap (it's always fairly cheap, but it was also on sale for $50), comes on a cardboard spool, and it prints fairly well. The vast majority of my prints are functional and I don't really care what color they are.

That said, my surface finish is a out 100 times better on my Voron than it was on my old i3 clone. I suspect this is because my extruder doesn't have a grub screw and is geared so it doesn't rely on the stepper micro stepping. If you go back a little in my post history you can see an A/B between the two. If you have a direct drive ungeared extruder it might be worth looking at upgrading if you want to improve surface finish.

[-] nrezcm@lemmy.world 2 points 6 months ago

Looks great! If I had a 3d printer I'd probably try doing the same with my 916+.

[-] tagginator@utter.online 0 points 6 months ago

New Lemmy Post: Very Specific Object: Made a wall mount for my NAS and its UPS (https://lemmy.world/post/12959824)
Tagging: #3dprinting

(Replying in the OP of this thread (NOT THIS BOT!) will appear as a comment in the lemmy discussion.)

I am a FOSS bot. Check my README: https://github.com/db0/lemmy-tagginator/blob/main/README.md

[-] stevedidwhat_infosec@infosec.pub -1 points 6 months ago

Keep that friendo updated and your net locked down! Synology seems to have a habit 😂

[-] IMALlama@lemmy.world 3 points 6 months ago

? Looks like your post ended too soon.

My Synology can access the Internet, but I don't have any ports forwarded to it.

[-] stevedidwhat_infosec@infosec.pub 1 points 6 months ago

Just had some nasty vulns for the web interfaces

this post was submitted on 10 Mar 2024
307 points (99.7% liked)

3DPrinting

15251 readers
35 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee